Msp430 usb debug interface msp fet430uif drivers for mac

MSP430 USB DEBUG INTERFACE MSP FET430UIF DRIVERS FOR MAC HOW TO
MSP430 USB DEBUG INTERFACE MSP FET430UIF DRIVERS FOR MAC INSTALL
MSP430 USB DEBUG INTERFACE MSP FET430UIF DRIVERS FOR MAC DRIVERS

Normally no changes need to be made to the MSP-FET430PIF's properties. Properties To see the properties associated with the MSP-FET430PIF, select the MSP-FET430PIF in the Targets window and view the properties in the Properties window. MSP430.DLL is included in every CrossWorks for MSP430 distribution.

MSP430 USB DEBUG INTERFACE MSP FET430UIF DRIVERS FOR MAC DRIVERS

Drivers No drivers are required for the MSP-FET430PIF. 2 AN-35 Using MSP430 Flash Emulation Tools with Rowley's CrossWorks for MSP430 on Windows XPДЈ TI's MSP430 Parallel-port Debugging Interface MSP-FET430PIF CrossWorks for MSP430 supports TI's MSP-FET430PIF (and all similar, compatible parallel-port MSP430 FETs) natively. This is also the recommended setting for interfacing a FET to Pumpkin's CubeSat Kit. Note In this Application Note, all interfaces are shown operating at +3.3V. Related Documents Pumpkin Application Note AN-34 This Application Note discusses issues surrounding the correct interfacing of FETs to the Pumpkin CubeSat Kit when taking the CubeSat Kit's operating voltage into account. Their use with operating systems other than Windows XP is likely to be similar to what is outlined in this Application Note.

Other Operating Systems Some FETs are also supplied with drivers for other operating systems (e.g.

Thus, you may need to follow the procedures outlined below each time you plug in a new FET or an existing FET into a different USB port. Note Each time a different device is attached to a Windows XP PC, 2 or even to a USB port different from the one it was first attached to, it is recognized as a unique device requiring drivers. USB device vendors supply product-specific drivers for their USB devices.

MSP430 USB DEBUG INTERFACE MSP FET430UIF DRIVERS FOR MAC INSTALL

When Windows XP discovers a new USB device, it attempts to identify and install the required driver(s) for each device. USB Device Installation Most modern Flash Emulation Tools connect to PCs via USB. Note The examples in this Application Note are for the MSP430F169, a mature device in the MSP430F16x/16xx family that does not include Spy-Bi-Wire support.

USB) FETs support the Spy-Bi-Wire feature included in newer MSP430s. Kalman on updated on All trademarks mentioned herein are properties of their respective companies.Дў MSP430 Devices The various FETs support different MSP430 families. Ignore these instructions at your own peril. Note The instructions contained herein especially the details concerning MSP430 DLL files may differ from those provided by the FET manufacturers.

The following popular FETs are covered in this application note: TI's MSP430 Parallel-Port Debugging Interface MSP-FET430PIF 1 TI's MSP430 USB Debugging Interface MSP-FET430UIF SoftBaugh's USBP Programmer / Debugger Olimex's MSP430 JTAG Tiny Rowley's MSP430 USB CrossConnect By following the instruction in this Application Note, you can run any combination of the MSP430 FETs listed above within CorssWorks for MSP430 without conflicts on a Windows XP PC.

MSP430 USB DEBUG INTERFACE MSP FET430UIF DRIVERS FOR MAC HOW TO

This Application Note Explains how to use FETs from different manufacturers with Rowley's CrossWorks for MSP430 v1.4. 1 AN-35 Application Note 744 Naples Street San Francisco, CA (415) Using MSP430 Flash Emulation Tools with Rowley's CrossWorks for MSP430 on Windows XP Introduction The programming and debugging interface to TI's MSP430 family of ultralow-power microcontrollers is via a low-cost Flash Emulation Tool (FET).

Msp430 usb debug interface msp fet430uif drivers for mac